122 lines
4.3 KiB
Plaintext
122 lines
4.3 KiB
Plaintext
loadrt [KINS]KINEMATICS
|
|
loadrt [EMCMOT]EMCMOT base_period_nsec=[EMCMOT]BASE_PERIOD servo_period_nsec=[EMCMOT]SERVO_PERIOD traj_period_nsec=[EMCMOT]SERVO_PERIOD key=[EMCMOT]SHMEM_KEY num_joints=[KINS]JOINTS
|
|
loadrt hal_parport cfg=0x378
|
|
setp parport.0.reset-time 4000
|
|
loadrt stepgen step_type=0,0,0,0
|
|
loadrt charge_pump
|
|
loadrt match8 count=1
|
|
|
|
loadrt pwmgen output_type=1
|
|
setp pwmgen.0.pwm-freq 5.0
|
|
#5000 RPM spindles (early production)
|
|
setp pwmgen.0.scale 5000
|
|
#7000 RPM spindles (late production)
|
|
#setp pwmgen.0.scale 7000
|
|
setp pwmgen.0.offset 0.0
|
|
setp pwmgen.0.min-dc 0.01
|
|
setp pwmgen.0.max-dc 0.99
|
|
setp pwmgen.0.dither-pwm true
|
|
|
|
addf parport.0.read base-thread
|
|
addf stepgen.make-pulses base-thread
|
|
addf charge-pump base-thread
|
|
addf pwmgen.make-pulses base-thread
|
|
addf parport.0.write base-thread
|
|
addf parport.0.reset base-thread
|
|
|
|
addf stepgen.capture-position servo-thread
|
|
addf motion-command-handler servo-thread
|
|
addf motion-controller servo-thread
|
|
addf stepgen.update-freq servo-thread
|
|
addf pwmgen.update servo-thread
|
|
addf match8.0 servo-thread
|
|
|
|
net spindle-cmd motion.spindle-speed-out pwmgen.0.value
|
|
net spindle-enable motion.spindle-on pwmgen.0.enable
|
|
|
|
net coolant-flood parport.0.pin-01-out iocontrol.0.coolant-flood
|
|
net xdir parport.0.pin-02-out stepgen.0.dir
|
|
net xstep parport.0.pin-03-out stepgen.0.step
|
|
setp parport.0.pin-03-out-reset 1
|
|
net ydir parport.0.pin-04-out stepgen.1.dir
|
|
net ystep parport.0.pin-05-out stepgen.1.step
|
|
setp parport.0.pin-05-out-reset 1
|
|
net zdir parport.0.pin-06-out stepgen.2.dir
|
|
net zstep parport.0.pin-07-out stepgen.2.step
|
|
setp parport.0.pin-07-out-reset 1
|
|
net adir parport.0.pin-08-out stepgen.3.dir
|
|
net astep parport.0.pin-09-out stepgen.3.step
|
|
setp parport.0.pin-09-out-reset 1
|
|
#PMDX-110
|
|
net spindle-dir parport.0.pin-14-out motion.spindle-reverse
|
|
#PMDX-131
|
|
#net spindle-dir parport.0.pin-14-out motion.spindle-forward
|
|
net spindle-pwm parport.0.pin-16-out pwmgen.0.pwm
|
|
net charge-pump parport.0.pin-17-out charge-pump.out
|
|
net estop-in parport.0.pin-10-in-not iocontrol.0.emc-enable-in
|
|
net estop-out charge-pump.enable halui.machine.is-on
|
|
#PMDX-110
|
|
net run parport.0.pin-11-in-not halui.program.pause motion.feed-hold
|
|
#PMDX-131
|
|
#net run parport.0.pin-11-in halui.program.pause motion.feed-hold
|
|
#normally closed switches (late production)
|
|
net all-home parport.0.pin-12-in
|
|
#normally open switches (early production)
|
|
#net all-home parport.0.pin-12-in-not
|
|
|
|
setp stepgen.0.position-scale [AXIS_0]SCALE
|
|
setp stepgen.0.steplen 1
|
|
setp stepgen.0.stepspace 0
|
|
setp stepgen.0.dirhold 35000
|
|
setp stepgen.0.dirsetup 16000
|
|
setp stepgen.0.maxaccel [AXIS_0]STEPGEN_MAXACCEL
|
|
net xpos-cmd axis.0.motor-pos-cmd stepgen.0.position-cmd
|
|
net xpos-fb stepgen.0.position-fb axis.0.motor-pos-fb
|
|
net xenable axis.0.amp-enable-out stepgen.0.enable
|
|
net all-home axis.0.home-sw-in
|
|
|
|
setp stepgen.1.position-scale [AXIS_1]SCALE
|
|
setp stepgen.1.steplen 1
|
|
setp stepgen.1.stepspace 0
|
|
setp stepgen.1.dirhold 35000
|
|
setp stepgen.1.dirsetup 16000
|
|
setp stepgen.1.maxaccel [AXIS_1]STEPGEN_MAXACCEL
|
|
net ypos-cmd axis.1.motor-pos-cmd stepgen.1.position-cmd
|
|
net ypos-fb stepgen.1.position-fb axis.1.motor-pos-fb
|
|
net yenable axis.1.amp-enable-out stepgen.1.enable
|
|
net all-home axis.1.home-sw-in
|
|
|
|
setp stepgen.2.position-scale [AXIS_2]SCALE
|
|
setp stepgen.2.steplen 1
|
|
setp stepgen.2.stepspace 0
|
|
setp stepgen.2.dirhold 35000
|
|
setp stepgen.2.dirsetup 16000
|
|
setp stepgen.2.maxaccel [AXIS_2]STEPGEN_MAXACCEL
|
|
net zpos-cmd axis.2.motor-pos-cmd stepgen.2.position-cmd
|
|
net zpos-fb stepgen.2.position-fb axis.2.motor-pos-fb
|
|
net zenable axis.2.amp-enable-out stepgen.2.enable
|
|
net all-home axis.2.home-sw-in
|
|
|
|
setp stepgen.3.position-scale [AXIS_3]SCALE
|
|
setp stepgen.3.steplen 1
|
|
setp stepgen.3.stepspace 0
|
|
setp stepgen.3.dirhold 35000
|
|
setp stepgen.3.dirsetup 16000
|
|
setp stepgen.3.maxaccel [AXIS_3]STEPGEN_MAXACCEL
|
|
net apos-cmd axis.3.motor-pos-cmd stepgen.3.position-cmd
|
|
net apos-fb stepgen.3.position-fb axis.3.motor-pos-fb
|
|
net aenable axis.3.amp-enable-out stepgen.3.enable
|
|
|
|
newsig false bit
|
|
sets false FALSE
|
|
net xhoming axis.0.homing match8.0.a0
|
|
net yhoming axis.1.homing match8.0.a1
|
|
net zhoming axis.2.homing match8.0.a2
|
|
net false match8.0.b0 match8.0.b1 match8.0.b2
|
|
net all-home match8.0.in
|
|
net limit match8.0.out axis.0.neg-lim-sw-in
|
|
|
|
# These loopbacks are usually disconnected by a postgui halfile
|
|
net tool-change-loop iocontrol.0.tool-change iocontrol.0.tool-changed
|
|
net tool-prepare-loopback iocontrol.0.tool-prepare iocontrol.0.tool-prepared
|