301 lines
10 KiB
Plaintext
301 lines
10 KiB
Plaintext
# HAL config file for Bridgeport BOSS.
|
|
#
|
|
# Load the core RT modules that will be needed.
|
|
|
|
# Kinematics
|
|
loadrt [KINS]KINEMATICS
|
|
|
|
# motion controller, get name and thread periods from ini file
|
|
loadrt [EMCMOT]EMCMOT servo_period_nsec=[EMCMOT]SERVO_PERIOD num_joints=[KINS]JOINTS
|
|
|
|
# PID module, for four PID loops
|
|
loadrt pid num_chan=4
|
|
|
|
# Install motenc driver.
|
|
loadrt hal_motenc
|
|
|
|
# Install PLC.
|
|
loadrt boss_plc
|
|
|
|
# Install debounce filters for operator console (cycle hold/start,
|
|
# limit override, spindle increase/decrease/status).
|
|
loadrt debounce cfg="7"
|
|
|
|
# Add functions to servo thread so they will be evaluated
|
|
# every servo period.
|
|
#
|
|
# Inputs are read at the beginning of the thread
|
|
addf debounce.0 servo-thread 1
|
|
addf motenc.0.encoder-read servo-thread 1
|
|
addf motenc.0.misc-update servo-thread 1
|
|
#addf motenc.0.adc-read servo-thread 1
|
|
addf motenc.0.digital-in-read servo-thread 1
|
|
# Do processing.
|
|
addf boss_plc.0.refresh servo-thread -1
|
|
addf motion-command-handler servo-thread -1
|
|
addf motion-controller servo-thread -1
|
|
addf pid.0.do-pid-calcs servo-thread -1
|
|
addf pid.1.do-pid-calcs servo-thread -1
|
|
addf pid.2.do-pid-calcs servo-thread -1
|
|
addf pid.3.do-pid-calcs servo-thread -1
|
|
# Outputs are updated at the end of the thread
|
|
addf motenc.0.dac-write servo-thread -1
|
|
addf motenc.0.digital-out-write servo-thread -1
|
|
|
|
# PID loops.
|
|
#
|
|
# Get maximum (and minimum) output volts from ini file.
|
|
setp pid.0.maxoutput [JOINT_0]MAX_OUTPUT
|
|
setp pid.1.maxoutput [JOINT_1]MAX_OUTPUT
|
|
setp pid.2.maxoutput [JOINT_2]MAX_OUTPUT
|
|
setp pid.3.maxoutput [JOINT_3]MAX_OUTPUT
|
|
|
|
# Set PID loop gains.
|
|
setp pid.0.Pgain [JOINT_0]P
|
|
setp pid.0.Igain [JOINT_0]I
|
|
setp pid.0.Dgain [JOINT_0]D
|
|
setp pid.0.bias [JOINT_0]BIAS
|
|
setp pid.0.FF0 [JOINT_0]FF0
|
|
setp pid.0.FF1 [JOINT_0]FF1
|
|
setp pid.0.FF2 [JOINT_0]FF2
|
|
# deadband should be just over 1 count
|
|
setp pid.0.deadband [JOINT_0]DEADBAND
|
|
|
|
setp pid.1.Pgain [JOINT_1]P
|
|
setp pid.1.Igain [JOINT_1]I
|
|
setp pid.1.Dgain [JOINT_1]D
|
|
setp pid.1.bias [JOINT_1]BIAS
|
|
setp pid.1.FF0 [JOINT_1]FF0
|
|
setp pid.1.FF1 [JOINT_1]FF1
|
|
setp pid.1.FF2 [JOINT_1]FF2
|
|
# deadband should be just over 1 count
|
|
setp pid.1.deadband [JOINT_1]DEADBAND
|
|
|
|
setp pid.2.Pgain [JOINT_2]P
|
|
setp pid.2.Igain [JOINT_2]I
|
|
setp pid.2.Dgain [JOINT_2]D
|
|
setp pid.2.bias [JOINT_2]BIAS
|
|
setp pid.2.FF0 [JOINT_2]FF0
|
|
setp pid.2.FF1 [JOINT_2]FF1
|
|
setp pid.2.FF2 [JOINT_2]FF2
|
|
# deadband should be just over 1 count
|
|
setp pid.2.deadband [JOINT_2]DEADBAND
|
|
|
|
setp pid.3.Pgain [JOINT_3]P
|
|
setp pid.3.Igain [JOINT_3]I
|
|
setp pid.3.Dgain [JOINT_3]D
|
|
setp pid.3.bias [JOINT_3]BIAS
|
|
setp pid.3.FF0 [JOINT_3]FF0
|
|
setp pid.3.FF1 [JOINT_3]FF1
|
|
setp pid.3.FF2 [JOINT_3]FF2
|
|
# deadband should be just over 1 count
|
|
setp pid.3.deadband [JOINT_3]DEADBAND
|
|
|
|
# Connect the enable signals to the PID blocks.
|
|
net xEnable joint.0.amp-enable-out => pid.0.enable
|
|
net yEnable joint.1.amp-enable-out => pid.1.enable
|
|
net zEnable joint.2.amp-enable-out => pid.2.enable
|
|
net aEnable joint.3.amp-enable-out => pid.3.enable
|
|
|
|
# Connect position commands to PID inputs.
|
|
net xPosCmd joint.0.motor-pos-cmd => pid.0.command
|
|
net yPosCmd joint.1.motor-pos-cmd => pid.1.command
|
|
net zPosCmd joint.2.motor-pos-cmd => pid.2.command
|
|
net aPosCmd joint.3.motor-pos-cmd => pid.3.command
|
|
|
|
# DACs
|
|
#
|
|
# Set DAC output scaling from ini file.
|
|
setp motenc.0.dac-01-gain [JOINT_0]OUTPUT_SCALE
|
|
setp motenc.0.dac-03-gain [JOINT_1]OUTPUT_SCALE
|
|
setp motenc.0.dac-02-gain [JOINT_2]OUTPUT_SCALE
|
|
setp motenc.0.dac-00-gain [JOINT_3]OUTPUT_SCALE
|
|
|
|
# Set DAC offset from ini file.
|
|
setp motenc.0.dac-01-offset [JOINT_0]OUTPUT_OFFSET
|
|
setp motenc.0.dac-03-offset [JOINT_1]OUTPUT_OFFSET
|
|
setp motenc.0.dac-02-offset [JOINT_2]OUTPUT_OFFSET
|
|
setp motenc.0.dac-00-offset [JOINT_3]OUTPUT_OFFSET
|
|
|
|
# Connect PID output signals to DACs.
|
|
net xOutput pid.0.output => motenc.0.dac-01-value
|
|
net yOutput pid.1.output => motenc.0.dac-03-value
|
|
net zOutput pid.2.output => motenc.0.dac-02-value
|
|
net aOutput pid.3.output => motenc.0.dac-00-value
|
|
|
|
# Encoders.
|
|
#
|
|
# Set feedback scaling from ini file.
|
|
setp motenc.0.enc-01-scale [JOINT_0]INPUT_SCALE
|
|
setp motenc.0.enc-03-scale [JOINT_1]INPUT_SCALE
|
|
setp motenc.0.enc-02-scale [JOINT_2]INPUT_SCALE
|
|
setp motenc.0.enc-00-scale [JOINT_3]INPUT_SCALE
|
|
|
|
# Connect position feedback to PID loop.
|
|
net xPosFb motenc.0.enc-01-position => pid.0.feedback
|
|
net yPosFb motenc.0.enc-03-position => pid.1.feedback
|
|
net zPosFb motenc.0.enc-02-position => pid.2.feedback
|
|
net aPosFb motenc.0.enc-00-position => pid.3.feedback
|
|
|
|
# Connect position feedback to motion module.
|
|
net xPosFb => joint.0.motor-pos-fb
|
|
net yPosFb => joint.1.motor-pos-fb
|
|
net zPosFb => joint.2.motor-pos-fb
|
|
net aPosFb => joint.3.motor-pos-fb
|
|
|
|
# Connect position feedback to PLC.
|
|
net xPosFb => boss_plc.0.x-position-in
|
|
net yPosFb => boss_plc.0.y-position-in
|
|
|
|
# Connect index pulses to motion controller.
|
|
net xIndex motenc.0.enc-01-index-enable <=> joint.0.index-enable
|
|
net yIndex motenc.0.enc-03-index-enable <=> joint.1.index-enable
|
|
net zIndex motenc.0.enc-02-index-enable <=> joint.2.index-enable
|
|
net aIndex motenc.0.enc-00-index-enable <=> joint.3.index-enable
|
|
|
|
# Limits.
|
|
#
|
|
# Connect limit/home switch inputs to PLC and motion controller.
|
|
net xLimitSw motenc.0.in-09 => boss_plc.0.x-limit-in
|
|
net xLimitSw => joint.0.home-sw-in
|
|
net yLimitSw motenc.0.in-13 => boss_plc.0.y-limit-in
|
|
net yLimitSw => joint.1.home-sw-in
|
|
net zMinlimSw motenc.0.in-26 => boss_plc.0.z-limit-neg-in
|
|
net zMaxlimSw motenc.0.in-25 => boss_plc.0.z-limit-pos-in
|
|
net zHome motenc.0.in-27 => joint.2.home-sw-in
|
|
|
|
# Connect PLC limit switch outputs to motion controller.
|
|
net xMinLim boss_plc.0.x-limit-neg-out => joint.0.neg-lim-sw-in
|
|
net xMaxLim boss_plc.0.x-limit-pos-out => joint.0.pos-lim-sw-in
|
|
net yMinLim boss_plc.0.y-limit-neg-out => joint.1.neg-lim-sw-in
|
|
net yMaxLim boss_plc.0.y-limit-pos-out => joint.1.pos-lim-sw-in
|
|
net zMinLim boss_plc.0.z-limit-neg-out => joint.2.neg-lim-sw-in
|
|
net zMaxLim boss_plc.0.z-limit-pos-out => joint.2.pos-lim-sw-in
|
|
|
|
# Amp enables/faults.
|
|
#
|
|
# Connect amp ready to PLC.
|
|
net xReady motenc.0.in-08 => boss_plc.0.x-amp-ready-in
|
|
net yReady motenc.0.in-12 => boss_plc.0.y-amp-ready-in
|
|
net zReady motenc.0.in-24 => boss_plc.0.z-amp-ready-in
|
|
net aReady motenc.0.in-28 => boss_plc.0.a-amp-ready-in
|
|
|
|
# Connect amp enables to I/O.
|
|
net xEnable => motenc.0.out-00
|
|
net yEnable => motenc.0.out-01
|
|
net zEnable => motenc.0.out-08
|
|
net aEnable => motenc.0.out-09
|
|
|
|
# Connect amp enables to PLC.
|
|
net xEnable => boss_plc.0.x-amp-enable-in
|
|
net yEnable => boss_plc.0.y-amp-enable-in
|
|
net zEnable => boss_plc.0.z-amp-enable-in
|
|
net aEnable => boss_plc.0.a-amp-enable-in
|
|
|
|
# Connect amp faults to motion controller.
|
|
net xFault boss_plc.0.x-amp-fault-out => joint.0.amp-fault-in
|
|
net yFault boss_plc.0.y-amp-fault-out => joint.1.amp-fault-in
|
|
net zFault boss_plc.0.z-amp-fault-out => joint.2.amp-fault-in
|
|
net aFault boss_plc.0.a-amp-fault-out => joint.3.amp-fault-in
|
|
|
|
# Spindle.
|
|
#
|
|
# Connect spindle speed to PLC and spindle fwd/rev/stat to I/O.
|
|
net spindleSpeed spindle.0.speed-out => boss_plc.0.spindle-speed-in
|
|
net spindleFwd boss_plc.0.spindle-fwd-out => motenc.0.out-11
|
|
net spindleRev boss_plc.0.spindle-rev-out => motenc.0.out-12
|
|
net spindleIsOnSw motenc.0.in-29-not => debounce.0.5.in
|
|
net spindleIsOnDly debounce.0.5.out => debounce.0.6.in
|
|
net spindleIsOn debounce.0.6.out => boss_plc.0.spindle-is-on-in
|
|
|
|
# Connect spindle brake to PLC and PLC brake to I/O.
|
|
setp boss_plc.0.brake-on-delay 500
|
|
setp boss_plc.0.brake-off-delay 800
|
|
net spindleBrakeOnMot spindle.0.brake => boss_plc.0.brake-en-in
|
|
setp motenc.0.out-02-invert 1
|
|
net spindleBrakeOn boss_plc.0.brake-en-out => motenc.0.out-02
|
|
|
|
# Tool change.
|
|
#
|
|
# Loop back tool prepare pins.
|
|
net toolPrepare iocontrol.0.tool-prepare iocontrol.0.tool-prepared
|
|
|
|
# Connect tool change pins to PLC.
|
|
net toolChange iocontrol.0.tool-change => boss_plc.0.tool-change-in
|
|
net toolChanged boss_plc.0.tool-changed-out => iocontrol.0.tool-changed
|
|
|
|
# Coolant.
|
|
#
|
|
# Connect mist/flood coolant to PLC.
|
|
net mistOnIo iocontrol.0.coolant-mist => boss_plc.0.mist-on-in
|
|
net floodOnIo iocontrol.0.coolant-flood => boss_plc.0.flood-on-in
|
|
|
|
# Connect mist/flood coolant to I/O.
|
|
net mistOn boss_plc.0.mist-on-out => motenc.0.out-14
|
|
net floodOn boss_plc.0.flood-on-out => motenc.0.out-15
|
|
|
|
# Operator console.
|
|
#
|
|
# Set debounce time.
|
|
setp debounce.0.delay 20
|
|
|
|
# Connect e-stop I/O.
|
|
net eStopSense motenc.0.in-32 => iocontrol.0.emc-enable-in
|
|
net eStopWrite iocontrol.0.user-enable-out => motenc.0.out-16
|
|
|
|
# Connect cycle hold/start.
|
|
net cycleHoldSw motenc.0.in-33-not => debounce.0.0.in
|
|
net cycleHold debounce.0.0.out => boss_plc.0.cycle-hold-in
|
|
net cycleStartSw motenc.0.in-34 => debounce.0.1.in
|
|
net cycleStart debounce.0.1.out => boss_plc.0.cycle-start-in
|
|
net feedHold boss_plc.0.feed-hold-out => motion.feed-hold
|
|
net waitUser boss_plc.0.wait-user-out => motenc.0.out-17
|
|
|
|
# Connect speed overrides.
|
|
net spindleIncSw motenc.0.enc-04-index => debounce.0.2.in
|
|
net spindleIncDb debounce.0.2.out => boss_plc.0.spindle-inc-in
|
|
net spindleInc boss_plc.0.spindle-inc-out => motenc.0.out-03
|
|
net spindleDecSw motenc.0.enc-06-index => debounce.0.3.in
|
|
net spindleDecDb debounce.0.3.out => boss_plc.0.spindle-dec-in
|
|
net spindleDec boss_plc.0.spindle-dec-out => motenc.0.out-04
|
|
|
|
# Connect limit override.
|
|
net limitOverrideSw motenc.0.in-35-not => debounce.0.4.in
|
|
net limitOverride debounce.0.4.out => boss_plc.0.limit-override-in
|
|
net limitActive boss_plc.0.limit-active-out => motenc.0.out-18
|
|
|
|
# Connect rapid/feed overrides.
|
|
net adaptiveFeed boss_plc.0.adaptive-feed-out => motion.adaptive-feed
|
|
setp halui.feed-override.scale 0.01
|
|
net feedOverride motenc.0.enc-04-count => halui.feed-override.counts
|
|
#net rapidOverride motenc.0.enc-06-count => halui.rapid-override.counts
|
|
|
|
# Set the jog mode so motion stops as soon as the wheel stops.
|
|
setp joint.0.jog-vel-mode TRUE
|
|
setp joint.1.jog-vel-mode TRUE
|
|
setp joint.2.jog-vel-mode TRUE
|
|
setp joint.3.jog-vel-mode TRUE
|
|
|
|
# Connect jog axis select to motion controller and PLC.
|
|
net xJog motenc.0.in-40 => joint.0.jog-enable
|
|
net yJog motenc.0.in-41 => joint.1.jog-enable
|
|
net zJog motenc.0.in-42 => joint.2.jog-enable
|
|
net aJog motenc.0.in-43 => joint.3.jog-enable
|
|
net xJog => boss_plc.0.x-jog-en-in
|
|
net yJog => boss_plc.0.y-jog-en-in
|
|
net zJog => boss_plc.0.z-jog-en-in
|
|
|
|
# Connect jog wheel encoder.
|
|
net jogCounts motenc.0.enc-05-count => joint.0.jog-counts joint.1.jog-counts joint.2.jog-counts joint.3.jog-counts
|
|
|
|
# Connect jog scale selects to PLC.
|
|
setp boss_plc.0.jog-scale-0 0.000001
|
|
setp boss_plc.0.jog-scale-1 0.000010
|
|
setp boss_plc.0.jog-scale-2 0.000100
|
|
net jogScaleSel0 motenc.0.in-36 => boss_plc.0.jog-sel-in-0
|
|
net jogScaleSel1 motenc.0.in-37 => boss_plc.0.jog-sel-in-1
|
|
net jogScaleSel2 motenc.0.in-38 => boss_plc.0.jog-sel-in-2
|
|
|
|
# Connect PLC jog scale output.
|
|
net jogScale boss_plc.0.jog-scale-out => joint.0.jog-scale joint.1.jog-scale joint.2.jog-scale joint.3.jog-scale
|