285 lines
8.3 KiB
INI
285 lines
8.3 KiB
INI
# EMC controller parameters for a plasma controller. Make these what you need
|
|
# for your system.
|
|
# General note: Comments can either be preceded with a # or ; - either is
|
|
# acceptable, although # is in keeping with most linux config files.
|
|
# Settings with a + at the front of the comment are likely needed to get
|
|
# changed by the user.
|
|
# Settings with a - at the front are highly unneeded to be changed
|
|
###############################################################################
|
|
# General section
|
|
###############################################################################
|
|
|
|
[EMC]
|
|
#- Version of this INI file
|
|
VERSION = 1.1
|
|
#+ Name of machine, for use with display, etc.
|
|
MACHINE = LinuxCNC-PLASMA-THC
|
|
#+ Debug level, 0 means no messages. See src/emc/nml_int/emcglb.h for others
|
|
DEBUG = 0
|
|
#DEBUG = 0x00000007
|
|
#DEBUG = 0x7FFFFFFF
|
|
# Enable Adaptive Feedrate for THC
|
|
# Used to pause execution of gcode for setup,
|
|
# pierce delay and manual verification of pierce height
|
|
# Set spindle speed to 1
|
|
# Set up to use metric mm
|
|
RS274NGC_STARTUP_CODE = M52 P1 G21 S1
|
|
###############################################################################
|
|
# Sections for display options
|
|
###############################################################################
|
|
|
|
[DISPLAY]
|
|
#Plasma Control Panel
|
|
PYVCP = thc_vcp.xml
|
|
#+ Name of display program, e.g., axis
|
|
DISPLAY = axis
|
|
#DISPLAY = tklinuxcnc
|
|
# Cycle time, in seconds, that display will sleep between polls
|
|
CYCLE_TIME = 0.200
|
|
#- Path to help file
|
|
HELP_FILE = doc/help.txt
|
|
#HELP_FILE = tklinuxcnc.txt
|
|
#- Initial display setting for position, RELATIVE or MACHINE
|
|
POSITION_OFFSET = RELATIVE
|
|
#- Initial display setting for position, COMMANDED or ACTUAL
|
|
POSITION_FEEDBACK = ACTUAL
|
|
#+ Highest value that will be allowed for feed override, 1.0 = 100%
|
|
MAX_FEED_OVERRIDE = 1.5
|
|
#- Prefix to be used
|
|
PROGRAM_PREFIX = ../../nc_files/
|
|
#- Text Editor
|
|
EDITOR = geany
|
|
#- Introductory graphic
|
|
INTRO_GRAPHIC = linuxcnc.gif
|
|
INTRO_TIME = 3
|
|
#Increments for the JOB Section
|
|
INCREMENTS = 1000 10 1 0.1 0.01
|
|
###############################################################################
|
|
# Task controller section
|
|
###############################################################################
|
|
|
|
[FILTER]
|
|
#No Content
|
|
|
|
[RS274NGC]
|
|
#- File containing interpreter variables
|
|
PARAMETER_FILE = plasma.var
|
|
###############################################################################
|
|
# Motion control section
|
|
###############################################################################
|
|
|
|
[EMCMOT]
|
|
#- Name of the motion controller to use (only one exists for nontrivkins)
|
|
EMCMOT = motmod
|
|
#- Timeout for comm to emcmot, in seconds
|
|
COMM_TIMEOUT = 1.0
|
|
#+ Base task period, in nanosecs - this is the fastest thread in the machine
|
|
#BASE_PERIOD = 15000
|
|
#BASE_PERIOD = 18000
|
|
#BASE_PERIOD = 20000
|
|
#BASE_PERIOD = 35000
|
|
BASE_PERIOD = 50000
|
|
#- Servo task period, in nanosecs - will be rounded to an int multiple of BASE_PERIOD
|
|
#SERVO_PERIOD = 10000
|
|
SERVO_PERIOD = 100000
|
|
#SERVO_PERIOD = 100000
|
|
#- Trajectory Planner task period, in nanosecs - will be rounded to an
|
|
# integer multiple of SERVO_PERIOD
|
|
#TRAJ_PERIOD = 100000
|
|
TRAJ_PERIOD = 1000000
|
|
###############################################################################
|
|
# Hardware Abstraction Layer section
|
|
###############################################################################
|
|
|
|
[TASK]
|
|
#- Name of task controller program, e.g., bridgeporttask
|
|
TASK = milltask
|
|
#- Cycle time, in seconds, that task controller will sleep between polls
|
|
CYCLE_TIME = 0.100
|
|
###############################################################################
|
|
# Part program interpreter section
|
|
###############################################################################
|
|
|
|
[HAL]
|
|
# The run script first uses halcmd to execute any HALFILE
|
|
# files, and then to execute any individual HALCMD commands.
|
|
#
|
|
# HALUI to interact with NML
|
|
# Run before any other HALFILE
|
|
HALUI = halui
|
|
# list of hal config files to run through halcmd
|
|
#+ files are executed in the order in which they appear
|
|
HALFILE = kinematics.hal
|
|
HALFILE = stepper.hal
|
|
HALFILE = stepper_parport.hal
|
|
HALFILE = estop.hal
|
|
HALFILE = thc.hal
|
|
HALFILE = axis_manualtoolchange.hal
|
|
HALFILE = simulator.hal
|
|
# A file to hook pyvcp to hal signals
|
|
POSTGUI_HALFILE = thc_vcp.hal
|
|
#- list of halcmd commands to execute
|
|
# commands are executed in the order in which they appear
|
|
#HALCMD = save neta
|
|
###############################################################################
|
|
# Trajectory planner section
|
|
###############################################################################
|
|
|
|
[HALUI]
|
|
#No Content
|
|
|
|
[TRAJ]
|
|
#+ machine specific settings
|
|
COORDINATES = X Y Z A
|
|
LINEAR_UNITS = mm
|
|
ANGULAR_UNITS = deg
|
|
#DEFAULT_VELOCITY = 100
|
|
DEFAULT_LINEAR_VELOCITY = 40
|
|
#MAX_VELOCITY = 180
|
|
MAX_LINEAR_VELOCITY = 63
|
|
DEFAULT_LINEAR_ACCELERATION = 600
|
|
MAX_LINEAR_ACCELERATION = 2400
|
|
#POSITION_FILE = last_position.txt
|
|
###############################################################################
|
|
# Axes sections
|
|
###############################################################################
|
|
#+ First axis (X)
|
|
|
|
[EMCIO]
|
|
#- Tool table file, torches and consumables
|
|
TOOL_TABLE = torches.tbl
|
|
#+ Tool Change Position, if this is set the torch will move the the specified position before requesting a tool change
|
|
#TOOL_CHANGE_POSITION = 0 0 50
|
|
|
|
[KINS]
|
|
KINEMATICS = trivkins coordinates=xyza kinematics=BOTH
|
|
JOINTS = 4
|
|
|
|
[AXIS_X]
|
|
MIN_LIMIT = -1
|
|
MAX_LIMIT = 2055
|
|
MAX_VELOCITY = 63
|
|
MAX_ACCELERATION = 2400
|
|
|
|
[JOINT_0]
|
|
TYPE = LINEAR
|
|
HOME = 0.000
|
|
#MAX_VELOCITY = 170
|
|
MAX_VELOCITY = 63
|
|
MAX_ACCELERATION = 2400
|
|
STEPGEN_MAXACCEL = 2960
|
|
BACKLASH = 0.000
|
|
SCALE = 150.333
|
|
OUTPUT_SCALE = 1.000
|
|
MIN_LIMIT = -1
|
|
MAX_LIMIT = 2055
|
|
FERROR = 1.270
|
|
MIN_FERROR = 0.254
|
|
HOME_OFFSET = 0.0
|
|
HOME_SEARCH_VEL = -50.0
|
|
HOME_LATCH_VEL = 1.0
|
|
HOME_USE_INDEX = NO
|
|
HOME_IGNORE_LIMITS = YES
|
|
HOME_SEQUENCE = 1
|
|
#+ Second axis (Y)
|
|
|
|
[AXIS_Y]
|
|
MIN_LIMIT = -1
|
|
MAX_LIMIT = 6050.0
|
|
MAX_VELOCITY = 63
|
|
MAX_ACCELERATION = 2400
|
|
|
|
[JOINT_1]
|
|
TYPE = LINEAR
|
|
HOME = 0.000
|
|
#MAX_VELOCITY = 170
|
|
MAX_VELOCITY = 63
|
|
MAX_ACCELERATION = 2400
|
|
STEPGEN_MAXVEL = 65
|
|
STEPGEN_MAXACCEL = 2960
|
|
BACKLASH = 0.000
|
|
SCALE = 150.333
|
|
OUTPUT_SCALE = 1.000
|
|
MIN_LIMIT = -1
|
|
MAX_LIMIT = 6050.0
|
|
FERROR = 1.270
|
|
MIN_FERROR = 0.254
|
|
HOME_OFFSET = 0.0
|
|
HOME_SEARCH_VEL = -50.0
|
|
HOME_LATCH_VEL = 1.0
|
|
HOME_USE_INDEX = NO
|
|
HOME_IGNORE_LIMITS = YES
|
|
HOME_SEQUENCE = 1
|
|
#+ Third axis (Z)
|
|
|
|
[AXIS_Z]
|
|
MIN_LIMIT = -1
|
|
MAX_LIMIT = 56.0
|
|
MAX_VELOCITY = 8
|
|
MAX_ACCELERATION = 600
|
|
|
|
[JOINT_2]
|
|
TYPE = LINEAR
|
|
HOME = 55.000
|
|
MAX_VELOCITY = 8
|
|
MAX_ACCELERATION = 600
|
|
STEPGEN_MAXACCEL = 650
|
|
#STEPGEN_MAXACCEL = 2960
|
|
BACKLASH = 0.000
|
|
SCALE = 200
|
|
OUTPUT_SCALE = 1.000
|
|
MIN_LIMIT = -1
|
|
MAX_LIMIT = 56.0
|
|
FERROR = 1.270
|
|
#MIN_FERROR = 0.254
|
|
# This is done so Z axis can be operated with a HAL closed loop (plasma THC)
|
|
MIN_FERROR = 500
|
|
HOME_OFFSET = 55.0
|
|
HOME_SEARCH_VEL = 10.0
|
|
HOME_LATCH_VEL = -2.0
|
|
HOME_USE_INDEX = NO
|
|
HOME_IGNORE_LIMITS = YES
|
|
HOME_SEQUENCE = 0
|
|
#+ Second axis (A)
|
|
|
|
[AXIS_A]
|
|
MIN_LIMIT = -1
|
|
MAX_LIMIT = 6050.0
|
|
MAX_VELOCITY = 63
|
|
MAX_ACCELERATION = 2400
|
|
|
|
[JOINT_3]
|
|
TYPE = LINEAR
|
|
HOME = 0.000
|
|
#MAX_VELOCITY = 170
|
|
MAX_VELOCITY = 63
|
|
MAX_ACCELERATION = 2400
|
|
STEPGEN_MAXACCEL = 2960
|
|
BACKLASH = 0.000
|
|
SCALE = 150.333
|
|
OUTPUT_SCALE = 1.000
|
|
MIN_LIMIT = -1
|
|
MAX_LIMIT = 6050.0
|
|
FERROR = 1.270
|
|
MIN_FERROR = 0.254
|
|
HOME_OFFSET = 0.0
|
|
HOME_SEARCH_VEL = -50.0
|
|
HOME_LATCH_VEL = 1.0
|
|
HOME_USE_INDEX = NO
|
|
HOME_IGNORE_LIMITS = YES
|
|
HOME_SEQUENCE = 1
|
|
###############################################################################
|
|
# section for main IO controller parameters
|
|
###############################################################################
|
|
|
|
[PLASMA]
|
|
# Note that setting Ignition timeout to high can cause issues with very short cuts, problems can arise when the timeout has not expired and starting to cut a new part
|
|
#- Ignition fault timeout, the time allowed from TorchOn until ArcOK before re-probing and re-initiating, in seconds
|
|
IGNITION_TIMEOUT = 3
|
|
#- ArcOK timeout, a filter, for a signal to be valid it needs to exceed the specified time period, in seconds
|
|
ARC_OK_FILTER_TIME = 0.2
|
|
#- Ignition Retries before abort, the number of attempts to re-probe and start the torch before estop
|
|
MAX_FAILED_IGNITIONS = 5
|
|
#- Extinguish Timeout, a grace period after losing ArcOK before shutting off the torch and re-probing, in seconds
|
|
EXTINGUISH_TIMEOUT = 0.2
|