108 lines
3.9 KiB
Plaintext
108 lines
3.9 KiB
Plaintext
# Generated by stepconf 1.1 at Mon Feb 28 16:28:49 2022
|
|
# If you make changes to this file, they will be
|
|
# overwritten when you run stepconf again
|
|
loadrt [KINS]KINEMATICS
|
|
loadrt [EMCMOT]EMCMOT base_period_nsec=[EMCMOT]BASE_PERIOD servo_period_nsec=[EMCMOT]SERVO_PERIOD num_joints=[KINS]JOINTS
|
|
loadrt hal_parport cfg="0 out"
|
|
setp parport.0.reset-time 5000
|
|
loadrt stepgen step_type=0,0,0,0
|
|
|
|
addf parport.0.read base-thread
|
|
addf stepgen.make-pulses base-thread
|
|
addf parport.0.write base-thread
|
|
addf parport.0.reset base-thread
|
|
|
|
addf stepgen.capture-position servo-thread
|
|
addf motion-command-handler servo-thread
|
|
addf motion-controller servo-thread
|
|
addf stepgen.update-freq servo-thread
|
|
net spindle-cmd-rpm <= spindle.0.speed-out
|
|
net spindle-cmd-rpm-abs <= spindle.0.speed-out-abs
|
|
net spindle-cmd-rps <= spindle.0.speed-out-rps
|
|
net spindle-cmd-rps-abs <= spindle.0.speed-out-rps-abs
|
|
net spindle-at-speed => spindle.0.at-speed
|
|
|
|
net xstep => parport.0.pin-02-out
|
|
setp parport.0.pin-02-out-reset 1
|
|
net xdir => parport.0.pin-03-out
|
|
net ystep => parport.0.pin-04-out
|
|
setp parport.0.pin-04-out-reset 1
|
|
net ydir => parport.0.pin-05-out
|
|
net zstep => parport.0.pin-06-out
|
|
setp parport.0.pin-06-out-reset 1
|
|
net zdir => parport.0.pin-07-out
|
|
net y2step => parport.0.pin-08-out
|
|
setp parport.0.pin-08-out-reset 1
|
|
net y2dir => parport.0.pin-09-out
|
|
|
|
#
|
|
# Very likely that you will have wired your limit/home switches differently.
|
|
#
|
|
net min-home-y2 <= parport.0.pin-10-in
|
|
net max-home-z <= parport.0.pin-11-in
|
|
net min-home-y <= parport.0.pin-12-in
|
|
net min-home-x <= parport.0.pin-13-in
|
|
|
|
setp stepgen.0.position-scale [JOINT_0]SCALE
|
|
setp stepgen.0.steplen 1
|
|
setp stepgen.0.stepspace 0
|
|
setp stepgen.0.dirhold 40000
|
|
setp stepgen.0.dirsetup 40000
|
|
setp stepgen.0.maxaccel [JOINT_0]STEPGEN_MAXACCEL
|
|
net xpos-cmd joint.0.motor-pos-cmd => stepgen.0.position-cmd
|
|
net xpos-fb stepgen.0.position-fb => joint.0.motor-pos-fb
|
|
net xstep <= stepgen.0.step
|
|
net xdir <= stepgen.0.dir
|
|
net xenable joint.0.amp-enable-out => stepgen.0.enable
|
|
net min-home-x => joint.0.home-sw-in
|
|
net min-home-x => joint.0.neg-lim-sw-in
|
|
|
|
setp stepgen.1.position-scale [JOINT_1]SCALE
|
|
setp stepgen.1.steplen 1
|
|
setp stepgen.1.stepspace 0
|
|
setp stepgen.1.dirhold 40000
|
|
setp stepgen.1.dirsetup 40000
|
|
setp stepgen.1.maxaccel [JOINT_1]STEPGEN_MAXACCEL
|
|
net ypos-cmd joint.1.motor-pos-cmd => stepgen.1.position-cmd
|
|
net ypos-fb stepgen.1.position-fb => joint.1.motor-pos-fb
|
|
net ystep <= stepgen.1.step
|
|
net ydir <= stepgen.1.dir
|
|
net yenable joint.1.amp-enable-out => stepgen.1.enable
|
|
net min-home-y => joint.1.home-sw-in
|
|
net min-home-y => joint.1.neg-lim-sw-in
|
|
|
|
setp stepgen.2.position-scale [JOINT_2]SCALE
|
|
setp stepgen.2.steplen 1
|
|
setp stepgen.2.stepspace 0
|
|
setp stepgen.2.dirhold 40000
|
|
setp stepgen.2.dirsetup 40000
|
|
setp stepgen.2.maxaccel [JOINT_2]STEPGEN_MAXACCEL
|
|
net zpos-cmd joint.2.motor-pos-cmd => stepgen.2.position-cmd
|
|
net zpos-fb stepgen.2.position-fb => joint.2.motor-pos-fb
|
|
net zstep <= stepgen.2.step
|
|
net zdir <= stepgen.2.dir
|
|
net zenable joint.2.amp-enable-out => stepgen.2.enable
|
|
net max-home-z => joint.2.home-sw-in
|
|
net max-home-z => joint.2.pos-lim-sw-in
|
|
|
|
setp stepgen.3.position-scale [JOINT_3]SCALE
|
|
setp stepgen.3.steplen 1
|
|
setp stepgen.3.stepspace 0
|
|
setp stepgen.3.dirhold 40000
|
|
setp stepgen.3.dirsetup 40000
|
|
setp stepgen.3.maxaccel [JOINT_3]STEPGEN_MAXACCEL
|
|
net y2pos-cmd joint.3.motor-pos-cmd => stepgen.3.position-cmd
|
|
net y2pos-fb stepgen.3.position-fb => joint.3.motor-pos-fb
|
|
net y2step <= stepgen.3.step
|
|
net y2dir <= stepgen.3.dir
|
|
net y2enable joint.3.amp-enable-out => stepgen.3.enable
|
|
net min-home-y2 => joint.3.home-sw-in
|
|
net min-home-y2 => joint.3.neg-lim-sw-in
|
|
|
|
net estop-out <= iocontrol.0.user-enable-out
|
|
net estop-out => iocontrol.0.emc-enable-in
|
|
|
|
net tool-number <= iocontrol.0.tool-prep-number
|
|
net tool-change-loopback iocontrol.0.tool-change => iocontrol.0.tool-changed
|
|
net tool-prepare-loopback iocontrol.0.tool-prepare => iocontrol.0.tool-prepared
|