Import LinuxCNC source tree
This commit is contained in:
Wang Dequan
107
tests/ccomp/mill-zchanges/expected
Normal file
107
tests/ccomp/mill-zchanges/expected
Normal file
@@ -0,0 +1,107 @@
|
||||
N..... USE_LENGTH_UNITS(CANON_UNITS_MM)
|
||||
N..... SET_G5X_OFFSET(1, 0.0000, 0.0000, 0.0000, 0.0000, 0.0000, 0.0000)
|
||||
N..... SET_G92_OFFSET(0.0000, 0.0000, 0.0000, 0.0000, 0.0000, 0.0000)
|
||||
N..... SET_XY_ROTATION(0.0000)
|
||||
N..... SET_FEED_REFERENCE(CANON_XYZ)
|
||||
N..... ON_RESET()
|
||||
N..... SET_FEED_RATE(60.0000)
|
||||
N..... USE_LENGTH_UNITS(CANON_UNITS_INCHES)
|
||||
N..... COMMENT("arc entry")
|
||||
N..... COMMENT("uncomp")
|
||||
N..... STRAIGHT_TRAVERSE(0.0000, 0.5000, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... STRAIGHT_FEED(0.2500, 0.5000, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... COMMENT("interpreter: cutter radius compensation on left")
|
||||
N..... ARC_FEED(0.5000, 0.7500, 0.5000, 0.5000, -1, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... STRAIGHT_FEED(0.7500, 0.7500, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... COMMENT("interpreter: cutter radius compensation off")
|
||||
N..... STRAIGHT_FEED(1.0000, 0.7500, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... STRAIGHT_FEED(1.2500, 0.7500, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... COMMENT("comp")
|
||||
N..... STRAIGHT_TRAVERSE(0.0000, 0.5000, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... STRAIGHT_FEED(0.2500, 0.5000, 0.0000, 0.0000, 0.0000, 0.0000)
|
||||
N..... COMMENT("interpreter: cutter radius compensation on left")
|
||||
N..... ARC_FEED(0.5000, 0.8125, 0.5000, 0.5562, -1, 0.0000, 0.0000, 0.0000, 0.0000)
|
||||
N..... STRAIGHT_FEED(0.7500, 0.8125, 0.0000, 0.0000, 0.0000, 0.0000)
|
||||
N..... COMMENT("interpreter: cutter radius compensation off")
|
||||
N..... STRAIGHT_FEED(1.0000, 0.7500, 0.0000, 0.0000, 0.0000, 0.0000)
|
||||
N..... STRAIGHT_FEED(1.2500, 0.7500, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... STRAIGHT_TRAVERSE(0.0000, 0.5000, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... STRAIGHT_FEED(0.2500, 0.5000, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... COMMENT("interpreter: cutter radius compensation on left")
|
||||
N..... ARC_FEED(0.5000, 0.8125, 0.5000, 0.5562, -1, 0.0000, 0.0000, 0.0000, 0.0000)
|
||||
N..... STRAIGHT_FEED(0.7500, 0.8125, 0.0000, 0.0000, 0.0000, 0.0000)
|
||||
N..... COMMENT("interpreter: cutter radius compensation off")
|
||||
N..... STRAIGHT_FEED(1.0000, 0.7500, 0.0000, 0.0000, 0.0000, 0.0000)
|
||||
N..... STRAIGHT_FEED(1.2500, 0.7500, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... STRAIGHT_TRAVERSE(0.0000, 0.5000, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... STRAIGHT_FEED(0.2500, 0.5000, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... COMMENT("interpreter: cutter radius compensation on left")
|
||||
N..... ARC_FEED(0.5000, 0.8125, 0.5000, 0.5562, -1, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... STRAIGHT_FEED(0.7500, 0.8125, 0.0000, 0.0000, 0.0000, 0.0000)
|
||||
N..... COMMENT("interpreter: cutter radius compensation off")
|
||||
N..... STRAIGHT_FEED(1.0000, 0.7500, 0.0000, 0.0000, 0.0000, 0.0000)
|
||||
N..... STRAIGHT_FEED(1.2500, 0.7500, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... STRAIGHT_TRAVERSE(0.0000, 0.5000, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... STRAIGHT_FEED(0.2500, 0.5000, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... COMMENT("interpreter: cutter radius compensation on left")
|
||||
N..... ARC_FEED(0.5000, 0.8125, 0.5000, 0.5562, -1, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... STRAIGHT_FEED(0.7500, 0.8125, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... COMMENT("interpreter: cutter radius compensation off")
|
||||
N..... STRAIGHT_FEED(1.0000, 0.7500, 0.0000, 0.0000, 0.0000, 0.0000)
|
||||
N..... STRAIGHT_FEED(1.2500, 0.7500, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... COMMENT("line entry")
|
||||
N..... COMMENT("uncomp")
|
||||
N..... STRAIGHT_TRAVERSE(0.0000, -0.5000, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... STRAIGHT_FEED(0.2500, -0.5000, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... COMMENT("interpreter: cutter radius compensation on left")
|
||||
N..... STRAIGHT_FEED(0.5000, -0.2500, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... STRAIGHT_FEED(0.7500, -0.2500, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... COMMENT("interpreter: cutter radius compensation off")
|
||||
N..... STRAIGHT_FEED(1.0000, -0.2500, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... STRAIGHT_FEED(1.2500, -0.2500, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... COMMENT("comp")
|
||||
N..... STRAIGHT_TRAVERSE(0.0000, -0.5000, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... STRAIGHT_FEED(0.2500, -0.5000, 0.0000, 0.0000, 0.0000, 0.0000)
|
||||
N..... COMMENT("interpreter: cutter radius compensation on left")
|
||||
N..... STRAIGHT_FEED(0.4558, -0.2058, 0.0000, 0.0000, 0.0000, 0.0000)
|
||||
N..... ARC_FEED(0.5000, -0.1875, 0.5000, -0.2500, -1, 0.0000, 0.0000, 0.0000, 0.0000)
|
||||
N..... STRAIGHT_FEED(0.7500, -0.1875, 0.0000, 0.0000, 0.0000, 0.0000)
|
||||
N..... COMMENT("interpreter: cutter radius compensation off")
|
||||
N..... STRAIGHT_FEED(1.0000, -0.2500, 0.0000, 0.0000, 0.0000, 0.0000)
|
||||
N..... STRAIGHT_FEED(1.2500, -0.2500, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... STRAIGHT_TRAVERSE(0.0000, -0.5000, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... STRAIGHT_FEED(0.2500, -0.5000, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... COMMENT("interpreter: cutter radius compensation on left")
|
||||
N..... STRAIGHT_FEED(0.4558, -0.2058, 0.0000, 0.0000, 0.0000, 0.0000)
|
||||
N..... ARC_FEED(0.5000, -0.1875, 0.5000, -0.2500, -1, 0.0000, 0.0000, 0.0000, 0.0000)
|
||||
N..... STRAIGHT_FEED(0.7500, -0.1875, 0.0000, 0.0000, 0.0000, 0.0000)
|
||||
N..... COMMENT("interpreter: cutter radius compensation off")
|
||||
N..... STRAIGHT_FEED(1.0000, -0.2500, 0.0000, 0.0000, 0.0000, 0.0000)
|
||||
N..... STRAIGHT_FEED(1.2500, -0.2500, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... STRAIGHT_TRAVERSE(0.0000, -0.5000, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... STRAIGHT_FEED(0.2500, -0.5000, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... COMMENT("interpreter: cutter radius compensation on left")
|
||||
N..... STRAIGHT_FEED(0.4558, -0.2058, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... ARC_FEED(0.5000, -0.1875, 0.5000, -0.2500, -1, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... STRAIGHT_FEED(0.7500, -0.1875, 0.0000, 0.0000, 0.0000, 0.0000)
|
||||
N..... COMMENT("interpreter: cutter radius compensation off")
|
||||
N..... STRAIGHT_FEED(1.0000, -0.2500, 0.0000, 0.0000, 0.0000, 0.0000)
|
||||
N..... STRAIGHT_FEED(1.2500, -0.2500, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... STRAIGHT_TRAVERSE(0.0000, -0.5000, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... STRAIGHT_FEED(0.2500, -0.5000, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... COMMENT("interpreter: cutter radius compensation on left")
|
||||
N..... STRAIGHT_FEED(0.4558, -0.2058, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... ARC_FEED(0.5000, -0.1875, 0.5000, -0.2500, -1, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... STRAIGHT_FEED(0.7500, -0.1875, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... COMMENT("interpreter: cutter radius compensation off")
|
||||
N..... STRAIGHT_FEED(1.0000, -0.2500, 0.0000, 0.0000, 0.0000, 0.0000)
|
||||
N..... STRAIGHT_FEED(1.2500, -0.2500, 0.2500, 0.0000, 0.0000, 0.0000)
|
||||
N..... SET_G5X_OFFSET(1, 0.0000, 0.0000, 0.0000, 0.0000, 0.0000, 0.0000)
|
||||
N..... SET_XY_ROTATION(0.0000)
|
||||
N..... SET_FEED_MODE(0, 0)
|
||||
N..... SET_FEED_RATE(0.0000)
|
||||
N..... STOP_SPINDLE_TURNING(0)
|
||||
N..... SET_SPINDLE_MODE(0 0.0000)
|
||||
N..... PROGRAM_END()
|
||||
N..... ON_RESET()
|
||||
N..... ON_RESET()
|
||||
81
tests/ccomp/mill-zchanges/test.ngc
Normal file
81
tests/ccomp/mill-zchanges/test.ngc
Normal file
@@ -0,0 +1,81 @@
|
||||
g20 f60
|
||||
|
||||
(arc entry)
|
||||
(uncomp)
|
||||
g0x0y.5z.25
|
||||
g1x.25
|
||||
g41 g2 d0 x.5 y.75 i.25
|
||||
g1 x.75
|
||||
g40 x1
|
||||
x1.25 z.25
|
||||
|
||||
(comp)
|
||||
g0x0y.5z.25
|
||||
g1x.25 z0
|
||||
g41 g2 d2 x.5 y.75 i.25
|
||||
g1 x.75
|
||||
g40 x1
|
||||
x1.25 z.25
|
||||
|
||||
g0x0y.5z.25
|
||||
g1x.25
|
||||
g41 g2 d2 x.5 y.75 i.25 z0
|
||||
g1 x.75
|
||||
g40 x1
|
||||
x1.25 z.25
|
||||
|
||||
g0x0y.5z.25
|
||||
g1x.25
|
||||
g41 g2 d2 x.5 y.75 i.25
|
||||
g1 x.75 z0
|
||||
g40 x1
|
||||
x1.25 z.25
|
||||
|
||||
g0x0y.5z.25
|
||||
g1x.25
|
||||
g41 g2 d2 x.5 y.75 i.25
|
||||
g1 x.75
|
||||
g40 x1 z0
|
||||
x1.25 z.25
|
||||
|
||||
|
||||
(line entry)
|
||||
(uncomp)
|
||||
g0x0y-.5z.25
|
||||
g1x.25
|
||||
g41 g1 d0 x.5 y-.25
|
||||
g1 x.75
|
||||
g40 x1
|
||||
x1.25 z.25
|
||||
|
||||
(comp)
|
||||
g0x0y-.5z.25
|
||||
g1x.25 z0
|
||||
g41 g1 d2 x.5 y-.25
|
||||
g1 x.75
|
||||
g40 x1
|
||||
x1.25 z.25
|
||||
|
||||
g0x0y-.5z.25
|
||||
g1x.25
|
||||
g41 g1 d2 x.5 y-.25 z0
|
||||
g1 x.75
|
||||
g40 x1
|
||||
x1.25 z.25
|
||||
|
||||
g0x0y-.5z.25
|
||||
g1x.25
|
||||
g41 g1 d2 x.5 y-.25
|
||||
g1 x.75 z0
|
||||
g40 x1
|
||||
x1.25 z.25
|
||||
|
||||
g0x0y-.5z.25
|
||||
g1x.25
|
||||
g41 g1 d2 x.5 y-.25
|
||||
g1 x.75
|
||||
g40 x1 z0
|
||||
x1.25 z.25
|
||||
|
||||
|
||||
m2
|
||||
3
tests/ccomp/mill-zchanges/test.sh
Normal file
3
tests/ccomp/mill-zchanges/test.sh
Normal file
@@ -0,0 +1,3 @@
|
||||
#!/bin/bash
|
||||
rs274 -t test.tbl -g test.ngc | awk '{$1=""; print}'
|
||||
exit "${PIPESTATUS[0]}"
|
||||
5
tests/ccomp/mill-zchanges/test.tbl
Normal file
5
tests/ccomp/mill-zchanges/test.tbl
Normal file
@@ -0,0 +1,5 @@
|
||||
T1 P1 Z0.5 D0.0625;first tool
|
||||
T2 P2 Z0.7 D0.125;
|
||||
T3 P3 Z0.5 D0.25;
|
||||
T4 P4 Z0.7 D1.0;
|
||||
T32 P32 Z0.5 D0.0;last tool
|
||||
Reference in New Issue
Block a user