wangdequan/linuxcncAllWasm
1
0
Fork 0
Code Issues Pull Requests Actions Packages Projects Releases Wiki Activity

Import LinuxCNC source tree

Browse Source
This commit is contained in:
Wang Dequan
2026-08-20 06:17:39 +08:00
commit 2c814634c3
9429 changed files with 10556013 additions and 0 deletions
Download Patch File Download Diff File Expand all files Collapse all files

66
configs/by_interface/mesa/hm2-modbus/brushless-dc-motor-driver.mbccs Normal file
View File

@@ -0,0 +1,66 @@
<?xml version="1.0" encoding="UTF-8"?>
<!--
Control board: AQMD2403BLS-M
The Brushless DC motor controller as been configured to run at
8E1@57600. The snag is that this board will not start at that speed on
power up. It starts at 8E1@9600 with a risk of the first packet to be
discarded.
The board has manually been set to 57600 baud by writing the two
registers with values:
- 0x0000 to register 0x0090
- 0xe100 to register 0x0091
using the W_REGISTERS(16) function. This data is stored in non-volatile
memory of the board, but it is first loaded when writing 0x0001 to
register 0x009d, and that must be done at every boot.
The initialization will downgrade to 9600 baud (board's default) and
then send the config change. That will immediately change baudrate and
the communication is flushed using a dummy transaction.
-->
<mesamodbus baudrate="57600" parity="E" stopbits="1" interval="50000" suspend="true">
<devices> <!-- Devices on the same bus -->
<device address="0x01" name="bldc" />
<device address="0x55" name="dummy" />
</devices>
<initlist> <!-- Initialization sequences -->
<!-- Default baudrate for bldc board at boot -->
<command baudrate="9600" />
<!-- Flush the bus so that the receiver is in a known state. -->
<command device="dummy" function="W_COIL" address="0x0000" noanswer="1"><data value="0xff00" /></command>
<!-- Set the board to the stored higher baudrate. -->
<command device="bldc" function="W_REGISTER" address="0x009d" timesout="true"><data value="1" /></command>
<!-- Restore our real baudrate -->
<command baudrate="57600" />
<!-- Again flush the bus so that the receiver is in a known state at the new baudrate. -->
<command device="dummy" function="W_COIL" address="0x0000" noanswer="1"><data value="0xff00" /></command>
</initlist>
<commands> <!-- Command function sequences and HAL pin assignments -->
<command device="bldc" function="R_REGISTERS" address="0x0020" modbustype="U_AB" haltype="S32" scale="1">
<pin name="rtpwm"/>
<pin name="rtcurrent"/>
<pin name="comfreq" modbustype="S_AB"/>
<pin skip="1" />
<pin name="rtpos" modbustype="S_ABCD" scale="0"/>
</command>
<!-- Gives us the following pins:
- hm2_modbus.0.bldc.rtpwm (out, s32) (range [0..65535])
- hm2_modbus.0.bldc.rtpwm.offset (in, u64)
- hm2_modbus.0.bldc.rtpwm.scale (in, float) (must be set to 0.1)
- hm2_modbus.0.bldc.rtpwm.scaled (out, float)
- hm2_modbus.0.bldc.rtcurrent (out, s32) (range [0..65535])
- hm2_modbus.0.bldc.rtcurrent.offset (in, u64)
- hm2_modbus.0.bldc.rtcurrent.scale (in, float) (must be set to 0.01)
- hm2_modbus.0.bldc.rtcurrent.scaled (out, float)
- hm2_modbus.0.bldc.comfreq (out, s32) (range [-32768..+32767])
- hm2_modbus.0.bldc.comfreq.offset (in, s64)
- hm2_modbus.0.bldc.comfreq.scale (in, float) (must be set to 0.1)
- hm2_modbus.0.bldc.comfreq.scaled (out, float)
- hm2_modbus.0.bldc.rtpos (out, s32) (range [-2147483648..+2147483647])
The start will be suspended (see top). The .scale pins will be set in
the hal-file. Offset pins are automatically initialized to zero.
Afterwards, the hal-file will enable communication.
-->
</commands>
</mesamodbus>