wangdequan
3c0f3fdc7c
结论：minimal interpreter harness 已按 LinuxCNC Interp::init 对齐 G73/G83 毫米默认 peck-clearance，canned_cycles 已纳入 upstream rs274 side-by-side baseline，完整 native probes 验证通过。
37 lines
2.4 KiB
Plaintext
37 lines
2.4 KiB
Plaintext
canon_event=STRAIGHT_TRAVERSE line=1 x=0 y=0 z=1 a=0 b=0 c=0 u=0 v=0 w=0
|
|
canon_event=SET_FEED_RATE rate=20
|
|
canon_event=STRAIGHT_TRAVERSE line=2 x=1 y=2 z=1 a=0 b=0 c=0 u=0 v=0 w=0
|
|
canon_event=STRAIGHT_TRAVERSE line=2 x=1 y=2 z=0.1 a=0 b=0 c=0 u=0 v=0 w=0
|
|
canon_event=STRAIGHT_FEED line=2 x=1 y=2 z=-0.5 a=0 b=0 c=0 u=0 v=0 w=0
|
|
canon_event=STRAIGHT_TRAVERSE line=2 x=1 y=2 z=0.1 a=0 b=0 c=0 u=0 v=0 w=0
|
|
canon_event=COMMENT: interpreter: motion mode set to none
|
|
canon_event=SET_FEED_RATE rate=25
|
|
canon_event=STRAIGHT_TRAVERSE line=4 x=1 y=2 z=0.2 a=0 b=0 c=0 u=0 v=0 w=0
|
|
canon_event=STRAIGHT_TRAVERSE line=4 x=2 y=3 z=0.2 a=0 b=0 c=0 u=0 v=0 w=0
|
|
canon_event=STRAIGHT_FEED line=4 x=2 y=3 z=-0.25 a=0 b=0 c=0 u=0 v=0 w=0
|
|
canon_event=DWELL seconds=0.15
|
|
canon_event=STRAIGHT_TRAVERSE line=4 x=2 y=3 z=0.2 a=0 b=0 c=0 u=0 v=0 w=0
|
|
canon_event=COMMENT: interpreter: motion mode set to none
|
|
canon_event=SET_FEED_RATE rate=30
|
|
canon_event=STRAIGHT_TRAVERSE line=6 x=3 y=4 z=0.2 a=0 b=0 c=0 u=0 v=0 w=0
|
|
canon_event=STRAIGHT_TRAVERSE line=6 x=3 y=4 z=0.15 a=0 b=0 c=0 u=0 v=0 w=0
|
|
canon_event=STRAIGHT_FEED line=6 x=3 y=4 z=-0.1 a=0 b=0 c=0 u=0 v=0 w=0
|
|
canon_event=STRAIGHT_TRAVERSE line=6 x=3 y=4 z=0.15 a=0 b=0 c=0 u=0 v=0 w=0
|
|
canon_event=STRAIGHT_TRAVERSE line=6 x=3 y=4 z=0.9 a=0 b=0 c=0 u=0 v=0 w=0
|
|
canon_event=STRAIGHT_FEED line=6 x=3 y=4 z=-0.35 a=0 b=0 c=0 u=0 v=0 w=0
|
|
canon_event=STRAIGHT_TRAVERSE line=6 x=3 y=4 z=0.15 a=0 b=0 c=0 u=0 v=0 w=0
|
|
canon_event=STRAIGHT_TRAVERSE line=6 x=3 y=4 z=0.65 a=0 b=0 c=0 u=0 v=0 w=0
|
|
canon_event=STRAIGHT_FEED line=6 x=3 y=4 z=-0.6 a=0 b=0 c=0 u=0 v=0 w=0
|
|
canon_event=STRAIGHT_TRAVERSE line=6 x=3 y=4 z=0.15 a=0 b=0 c=0 u=0 v=0 w=0
|
|
canon_event=COMMENT: interpreter: motion mode set to none
|
|
canon_event=SET_FEED_RATE rate=35
|
|
canon_event=COMMENT: interpreter: distance mode changed to incremental
|
|
canon_event=STRAIGHT_TRAVERSE line=8 x=3 y=4 z=0.25 a=0 b=0 c=0 u=0 v=0 w=0
|
|
canon_event=STRAIGHT_TRAVERSE line=8 x=4 y=5 z=0.25 a=0 b=0 c=0 u=0 v=0 w=0
|
|
canon_event=STRAIGHT_FEED line=8 x=4 y=5 z=-0.15 a=0 b=0 c=0 u=0 v=0 w=0
|
|
canon_event=STRAIGHT_TRAVERSE line=8 x=4 y=5 z=0.25 a=0 b=0 c=0 u=0 v=0 w=0
|
|
canon_event=STRAIGHT_TRAVERSE line=8 x=5 y=6 z=0.25 a=0 b=0 c=0 u=0 v=0 w=0
|
|
canon_event=STRAIGHT_FEED line=8 x=5 y=6 z=-0.15 a=0 b=0 c=0 u=0 v=0 w=0
|
|
canon_event=STRAIGHT_TRAVERSE line=8 x=5 y=6 z=0.25 a=0 b=0 c=0 u=0 v=0 w=0
|
|
canon_event=COMMENT: interpreter: motion mode set to none
|